Why It Made the Cut
The SEVR broadheads are accurate, durable, and make pre-season practice easy.
Test Results
Pros
Cons
Product Description
The SEVR 1.5 and 2.0 are available in 100 and 125-grain weights. The ferrule is made from grade-5 titanium, and the blades are made from unspecified stainless steel. The blades are rear deploying, which means it’ll cut an entrance hole. Once deployed, the blades lock together and will pivot around bone rather than cut through it, which SEVR claims helps penetration.
Another interesting feature is how easy it is to practice with SEVRs. You just have to drop in the included set screw to lock the blades together. Then clean out the target residue, replace the o-ring, and remove the set screw when you’re ready to take them hunting. Another area where the SEVR stands out is its low-profile design, which results in accuracy at extended ranges. They were the most accurate mechanical in the test at 1.25 and 1.5-inch groups. Snyder has tested the SEVRs beyond 40 yards. “I can grab any SEVR and group at 100,” he said.
In the durability test, the blades had slight wrinkling but did not bend or break. I would treat the blades as single use, but the ferrule can be reused for multiple animals. Snyder has used the SEVRs on a lot of animals with great success. “I prefer the 2.0 for most things,” he said. “They’ve had a devastating effect on animals.” While Snyder prefers the 2.0, he reco*mends the 1.5 for elk.
The blades rattle, and you can hear them in your quiver, but Snyder has a solution for that issue. “I put wax between the blades to reduce the rattling,” he said
The SEVR 2.0s were sharp out of the package, but the 1.5s at 494 grams were not. I would reco*mend checking sharpness on SEVRs and touching them up if necessary. In the push force test the SEVRs did average among the mechanicals, and one design feature holding them back is the arms that deploy the blades because in the open position they are exposed and cause drag. That drag could be minimized if those arms were sharpened rather than rounded. In his testing notes Greenwood said that if a broadhead isn’t cutting, it’s pushing and that causes significant drag.
Why It Made the Cut
The Magnus Stinger is a proven broadhead that co*es sharp out of the box.
Test Results
Pros
Cons
Product Description
The Magnus Stinger is a stainless steel broadhead that co*es in weights from 85 to 150 grains and as a two or four blade. They’re an affordable head at around $40 for three. In the accuracy test they shot under a 3-inch group and went through the PVC pipe unscathed.
In the sharpness test, the Stingers were right on the bubble for being considered ready to hunt. Two of the three heads met the 400-gram requirement, but one head was 50 grams over. In the gel test, the bleeder blades did not cut the gel, which reduced the wound channel. So I’d reco*mend touching up Stingers if you plan on taking them straight from the pack to the field.
In the push force test, the Stingers were a standout performer co*ing in fourth right behind heads costing more than double its price. If you need a broadhead that will penetrate well and you don’t want to spend $100 for three, then consider the Stingers.
Snyder has had great experiences with Stinger and his wife has used them successfully as well. “If I was on a budget, the Stinger would be at the top of my list,” he said.
Why It Made the Cut
The Day Six Evo 100 is an impressively sharp and accurate broadhead.
Test Results
Pros
Cons
Product Description
Day Six Evo 100‘s four blades are made from S30V steel and co*e in weights from 100 to 175 grains. S30V is known as a quality stainless steel used in knife making, and it carries the same edge retaining properties in the Evo 100.
S30V is known for its edge retention and corrosion resistance, but it’s also known to be brittle steel that’s prone to chip in hard use. That’s because the heat treatment required for S30V makes it hard steel. “The only downside of the Day Six is the steel can be brittle, but they’re a very good head,” Snyder said. With that said, in my durability test the Evo 100 sustained no damage, and the head looked like new. It also had the smallest groups of all the broadheads shot.
The Evo 100 was also the sharpest broadhead out of the package. It was around 150 grams, which puts it in the range of a razor blade. The reason that’s so impressive is that the Evo 100 has a much thicker blade than a razor. A key advantage of starting out so sharp is that in the edge retention test the head measured 222 grams, which is still well below our 400 gram sharpness mark. The head also did well in the push force test finishing third. Although one design feature that might have held it back from being the best is its forward bleeder blades (the Iron Will with its bleeders in the rear performed better).
Why It Made the Cut
The Deadmeat V2 has giant entry and exit holes created by very sharp and durable blades.
Test Results
Pros
Cons
Product Description
The Deadmeat V2 is a rear-deploying mechanical, available in 100 or 125 grains. The blades are retained by a collar rather than a band. Snyder cautions that the blades can deploy when caught on brush during a stalk, which is less of an issue for treestand hunters.
In the gel test, there were only a few broadheads that recorded a wound channel over two inches, and the Deadmeat V2 was one of them. “The Deadmeat is one of the most accurate and devastating mechanicals I’ve used,” Snyder said. Our testing confirmed his in-the-field experience. Aside from the large wound channel, the Deadmeat V2 was accurate, durable, and at 220 grams it was the third sharpest. It also did the second best of all the mechanicals in the push force test, despite its large cutting diameter. The blade sharpness and tip design were contributors to its ease of penetration.
Why It Made the Cut
This single-bevel broadhead has a track record for durability, accuracy, and penetration.
Test Results
Pros
Cons
Product Description
Single bevel broadheads might be the latest craze, but RMS Gear has been making their Cutthroat heads for years. One recent update is that they’re now made from S7 Tool Steel. S7 is known as a durable, impact-resistant steel with a relatively low hardness, which makes it ideal for a tough and easy-to-sharpen broadhead. “They’re probably the most durable broadheads I’ve used, and I don’t know if I’ve ever ruined one,” Freel said. The cutthroats don’t co*e sharp out of the package, but RMS Gear will sharpen them for an additional charge.
In addition to being durable, Freel has had excellent passthroughs with them out of his recurve. “I almost always get pass-throughs with the Cutthroat,” he said. “I shot through a bear’s scapula, and it was like it wasn’t even there.” What Freel saw in the field was also seen on the Cutthroat’s very low push force numbers.
Why It Made the Cut
This broadhead had the lowest push force number of all mechanical heads, the second largest wound channel, and shot sub-2-inch groups.
Test Results
Pros
Cons
Product Description
If there was one theme in the broadhead test it’s that short heads were more accurate. One of the main reasons for that is it’s harder to manufacture a long head with good tolerances. The Ramcat Diamondback Hybrid was an exception to that trend. It shot impressive groups and had very low spin run out. I also expect longer heads to be less durable, but this head looked like new after passing through the PVC pipe.
Hybrid broadheads have the reliability of fixed blade heads with the wide cut of mechanicals. The Diamondback Hybrid had the second largest wound channel because of its four-blade design. This head has Ramcat’s concave-scoop head and a single bevel fixed blade. I don’t know why Ramcat decided to go with a single bevel on a hybrid broadhead because it won’t spin while it cuts like a Cutthroat. But, the single bevel doesn’t seem to hurt the head’s performance. It also has two wide cutting mechanical blades that are secured with an o-ring. You can place that o-ring closer to the shaft or closer to the tip, depending on if you want the blades to be more secure or easier to open.
The Diamondback Hybrid also did the best of all the mechanicals in the push force test, which is surprising considering its large wound channel. At 339 grams the blades were also very sharp.
Why It Made the Cut
The Cutthroat 3 Blade is easy to sharpen, durable, and accurate.
Test Results
Pros
Cons
Product Description
The Cutthroat 3-Blade is available in 100, 125, 150, 200, and 250 grains. They’re CNC machined from high-carbon steel. One of the signature features of this head is the curved blades. “I found that the convex blade makes a larger wound channel,” Snyder said. “I shot an aoudad with them that had a blood trail about three feet wide for 40 yards.”
When you buy Cutthroat broadheads they will need to be sharpened before hunting. The good news is they’re pretty easy to sharpen thanks to the high-carbon steel and their design. Snyder finds that the Cutthroats are easier to sharpen than most three blades because the curved blades allow you to apply even pressure over the whole length of the bevel.
The Cutthroats did not do great in the push force test, which is mostly due to a high number during the edge media test. A sharp head would have cut those numbers down significantly. In the hide and ferrule test, the Cutthroat was an average performer. Another note is that we tested the 100 grain model, which is shorter and has a more obtuse angle than the longer, heavier versions offered.